Product ID:REXOLITE ADHESIVE # 12517
MSDS Date:03/20/1988
FSC:8040
NIIN:00-149-0649
Kit Part:Y
MSDS Number: BHWVQ

C-LEC PLASTICS, INC.

1717 BRIDGEBORO ROAD
BEVERLY, NJ 08010
US

Emergency Phone: 215-533-3553

Info Phone: 215-533-3553

Cage: 60956

C-LEC PLASTICS, INC.

BEVERLY, NJ 08010 US

Telephone: 215-533-3553

Cage: 60956

POLYSTYRENE

CAS: 9003-53-6

RTECS: WL6475000

DIVINYL BENZENE

CAS: 1321-74-0

RTECS: CZ9400000

OSHA PEL 10 PPM

ACGIH TLV: 10 PPM; 9192

LD50 LC50 Mixture:LD50 (ORAL RAT) IS 5000 MG/KG.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:REPEATED EXCESSIVE EXPOSURES TO HIGH
AMOUNTS MAY CAUSE CENTRAL NERVOUS SYSTEM, LIVER AND KIDNEY EFFECTS.
REPEATED EXCESSIVE EXPOSURES TO SMALLER AMOUNTS MAY CAUSE CENTRAL
NERVOUS SYSTEM EFFECTS AND RE SPIRATORY AND EYE IRRITATION.
Explanation of Carcinogenicity:NONE OF THE CHEMICALS IN THIS PRODUCT IS
LISTED BY IARC, NTP OR OSHA AS A CARCINOGEN.
Effects of Overexposure:EYES:IRRITATION,TEARING.
SKIN:IRRITATION,BURNS.REPEATED CONTACT MAY CAUSE DRYING OR FLAKING.
INHALATION:ANESTHETIC OR NARCOTIC EFFECTS.IRRITATION TO UPPER
RESPIRATORY TRACT.
Medical Cond Aggravated by Exposure:PERSONS WITH A HISTORY OF
RESPIRATORY DISORDERS MAY BE AT INCREASED RISK FROM EXPOSURE.

First Aid:EYES:IMMEDIATELY FLUSH WITH PLENTY OF WATER FOR AT LEAST 15
MINUTES.SEE DOCTOR. SKIN:IMMEDIATELY FLUSH WITH PLENTY OF WATER
WHILE REMOVING CONTAMINATED CLOTHING AND SHOES.IF IRRITATION
PERSIST,SEE DOC TOR. INHALATION:REMOVE TO FRESH AIR.IF NOT
BREATHING GIVE CPR.IF BREATHING IS DIFFICULT,GIVE OXYGEN.SEE
DOCTOR. INGESTION:DO NOT INDUCE VOMIT.SEE DOCTOR.

Flash Point Method:TCC
Flash Point:=31.1C, 88.F
Lower Limits:1.1
Upper Limits:6.1
Extinguishing Media:USE WATER FOG, CARBON DIOXIDE, FOAM, OR DRY
CHEMICAL.
Fire Fighting Procedures:FIRE FIGHTERS SHOULD USE NIOSH APPROVED SCBA &
FULL PROTECTIVE EQUIPMENT WHEN FIGHTING CHEMICAL FIRE. USE WATER
SPRAY TO COOL NEARBY CONTAINERS EXPOSED TO FIRE.
Unusual Fire/Explosion Hazard:POLYMERIZATION WILL TAKE PLACE UNDER FIRE
CONDITIONS AND CONTAINER MAY RUPTURE VIOLENTLY. COOL FIRE EXPOSED
CONTAINERS WITH WATER.

Spill Release Procedures:ABSORB WITH SUITABLE AGENT, SUCH AS SAND OR
VERMICULITE.WASH AREA WITH SOAP AND WATER. SOME ABSORBENTS SUCH AS
ZORB-ALL MAY INITIATE POLYMERIZATION.
Neutralizing Agent:NONE APPLICABLE FOR THIS MATERIAL

Handling and Storage Precautions:STORE IN COOL, DRY, WELL VENTILATED
AREA. PROTECT FROM PHYSICAL DAMAGE, HEAT AND IGNITION SOURCES. KEEP
CONTAINERS CLOSED.
Other Precautions:NONE.

Respiratory Protection:ATMOSPHERIC LEVELS SHOULD BE MAINTAINED BELOW
THE EXPOSURE GUIDELINE. WHEN RESPIRATORY PROTECTION IS REQUIRED FOR
CERTAIN OPERATIONS, USE AN APPROVED AIR-PURIFYING RESPIRATOR.
Ventilation:MECHANICAL (GENERAL) VENTILATION IS REQUIRED. LOCAL EXHAUST
MAY BE REQUIRED IF WORK AREA IS NOT VENTED.
Protective Gloves:IMPERVIOUS.
Eye Protection:CHEMICAL GOGGLES OR FULL FACE RESPIRATOR
Other Protective Equipment:IMPERVIOUS PROTECTIVE CLOTHING. USE OF
BOOTS, APRON OR FULL-BODY SUIT WILL DEPEND ON TYPE OF OPERATION.
Work Hygienic Practices:WASH THROUGHLY AFTER HANDLING AND BEFORE
EATING. LAUNDER CONTAMINATED CLOTHING BEFORE REUSE. DISCARD
CONTAMINATED SHOES.
Supplemental Safety and Health
NOTE TO PHYSICIAN:BECAUSE RAPID ABSORPTION MAY OCCUR THROUGH LUNGS IF
ASPIRATED,THE DECISION TO INDUCE VOMIT SHOULD BE MADE BY A
PHYSICIAN. IF LAVAGE IS PERFORMED,SUGGEST ENDOTRACHEAL AND/OR
ESOPHGEAL CONTROL. IF BURN IS PRESENT,TREAT AS ANY THERMAL BURN
AFTER DECONTAMINATION.NO SPECIFIC ANTIDOTE.SUPPORTIVE CARE.

HCC:F3
Boiling Pt:=145.C, 293.F
Vapor Pres:4.5
Spec Gravity:0.9034
Appearance and Odor:COLORLESS LIQUID. SWEET ODOR.

Stability Indicator/Materials to Avoid:NO
ACID, CAUSTIC, OXIDIZING MATERIAL, METALLIC HALIDES (SALTS).
Stability Condition to Avoid:POLYMERIZES EASILY. AVOID TEMPERATURES
ABOVE 90F. MAINTAIN INHIBITOR AND DISSOLVED OXYGEN LEVEL.
Hazardous Decomposition Products:CARBON DIOXIDE, CARBON MONOXIDE,
INCOMPLETELY BURNED CARBON PRODUCTS.
Conditions to Avoid Polymerization:AVOID HEAT, METALLIC (HALIDE) SALTS
SUCH AS FERRIC AND ALUMINUM CHLORIDES, PEROXIDES, AND DEPLETION OF
INHIBITOR & OXIGN

Waste Disposal Methods:INCINERATE IN PROPERLY DESIGNED FURNACE. DISPOSE
OF IN ACCORDANCE WITH ALL APPLICABLE FEDERAL, STATE AND LOCAL LAWS
AND REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.